Digging Deeper: Improving financial performance and reducing maintenance costs in mining

""

Some mine haul trucks feature $50,000 tires and consume up to 30 gallons of fuel an hour. It could cost over a million dollars a year to operate one of these mine haul trucks. These high costs are also combined with almost continuous use of equipment in mining industry. This combination allows even small improvements yield into major financial performance gains for miners. 

High purchase and maintenance costs of mining equipment and machinery
High purchase and maintenance costs of mining equipment and machinery

What impacts the financial performance of mining equipment and machinery?

Financial performance of mining equipment includes the cost to acquire, maintain and dispose the equipment. Mining equipment’s financial performance became a focal point for the industry at the end of the commodities boom in early 2000’s. Today, it continues to be a key focus point across types of mining

The primary driver of mining equipment’s financial performance is on-going costs such as fuel and consumables. This is because of the extensive utilization of mining equipment and machinery. For some Cummins Inc. customers, fuel cost by itself is 70% of an engine’s life cycle costs. For these customers, fuel cost is also about a quarter of equipment’s total cost of ownership.

Given the importance of equipment’s financial performance, let’s outline three ways the mining industry improves affordability.

No. 1: Leverage fuel savings to improve financial performance

Fuel continues to be the primary cost for operating the mines. This makes fuel consumption a significant opportunity to improve financial performance. One might, inaccurately, think the increasing focus on lowering emissions could increase fuel consumption. In fact, our experience at Cummins shows the exact opposite. Most of our newest Tier 4 Final engines (over 751 horsepower) offer up to 3 percent to 5 percent better fuel efficiency than our Tier 2 engines. Moreover, there is no compromise to engine power and reliability. 

Our partners have experienced similar fuel savings across different applications too. Check out how an iron ore mine that uses 850 million liters of diesel a year has experienced savings worth millions of dollars a year. The miner has accomplished this improvement in financial performance by combining component technology from both Cummins’ Tier 2 and Tier 4 Final engines.

No. 2: Reduce the use of other consumables to lower maintenance costs

A regular mine truck has a capacity for over 400 gallons of consumables. In comparison, your car might have only a few gallons of consumables. Beyond the liquid consumables, mine trucks also have fuel, lube oil, air and water filters that get changed  every 500 to 1,000 hours (about once a month). These all add up in the form of on-going maintenance costs. 

Save on consumables to improve your mining equipment’s financial performance
Save on consumables to improve your mining equipment’s financial performance

Potential savings in maintenance costs grow rapidly when you combine the frequency of changes and equipment usage patterns. For instance, a coal mine in Queensland, Australia experienced a cost savings of 60 percent through reduced filter and oil consumption alone. This has equaled to savings more than $220,000 per year for the fleet of 14 trucks. In a similar case, Colombia’s largest open-pit mine extended change intervals on fuel filters to 1,000 hours and air filters to 2,000 hours. The miner has used NanoNet™ Fuel Filters and NanoForce® Air Filters to accomplish this, and to minimize maintenance costs. Miners can further amplify these savings by adapting condition-based maintenance procedures offered by PrevenTech Mining

No. 3: Rebuild engines with the latest technology for better financial performance

The cyclical nature of the mining industry, and the rapid advancements in technology introduce a challenge for the miners: how to keep their equipment optimized for their evolving needs. Engine technologies continually advance to offer lower emissions and fuel consumption. These advancements offer benefits both in financial performance and environmental impact. Miners seek to reflect these advancements in their existing equipment. 

A mine truck, with proper maintenance, could see three to four engine re-builds. This is before the whole chassis needs to be re-built. Miners can improve their financial performance by optimizing their engines during these re-builds. For instance, one miner in Australia’s Bowen Basin concurrently lowered emissions and total cost of production, a gain in financial performance. The miner simply replaced the old engine fuel system with a Modular Common Rail fuel system (MCRS). The new configuration featured Cummins’ latest innovations in combustion technology from its Tier 4 engineering programs.

Whether it is through fuel savings or reduced use of consumables, gains in affordability also help on reducing environmental impact. Moreover, gains in affordability also favorably impact sustainable cost of production. Miners can experience these gains. The key is to seek partners, such as Cummins, that are technical leaders and have a track record in championing the latest innovations in power solution technologies. PrevenTech and FIT are two of these latest technologies. They leverage advanced analytics and connectivity in helping customers improve affordability of their operations,” said Sean Lynas, General Manager High Horse Power Business at Cummins.

Interested in additional mining perspectives? You might also like: 

Wanting to deepen and broaden your expertise in the mining industry? Sign up below to receive periodic insights, trends and news customized for the mining industry. To learn more about mining power solutions Cummins offers, visit The Power of Cummins Mining

Aytek Yuksel - Cummins Inc

Aytek Yuksel

Aytek Yuksel is the Content Marketing Leader for Cummins Inc., with a focus on Power Systems markets. Aytek joined the Company in 2008. Since then, he has worked in several marketing roles and now brings you the learnings from our key markets ranging from industrial to residential markets. Aytek lives in Minneapolis, Minnesota with his wife and two kids.

Unpacking CARB’s trucking rules, regulations and legal challenges

Semi truck driving

The state of California has positioned itself as a central figure in a revolutionary shift from a 100-year path of internal combustion engines (ICE) used in commercial transportation. Within a three-year span, the state has adopted the world’s most stringent commercial vehicle regulations: Advanced Clean Trucks (ACT), the Heavy-Duty Engine and Vehicle Omnibus Regulation and Advanced Clean Fleets (ACF). The three rules work together to gradually transition commercial trucks, buses and vans to zero emission vehicles (ZEVs).

The stringent regulations have generated plenty of praise, collaboration, concern and even legal challenges. Turning away from familiar and trusted technology will be anything but easy but the industry is proving it is possible.

Questions around ZEV cost and capability relative to ICE are not taken lightly by Cummins nor other players in one of the nation’s most critical industries.

As with prior emissions legislation, amendments will undoubtedly emerge as collaborative efforts between policymakers and industry continue. That is currently the case with the Omnibus regulation as proposed amendments are under review by the Environmental Protection Agency. Some of the amendments in question focus on diesel engine testing, warranty periods and aftertreatment. 

“Omnibus, the amended version, got resubmitted to EPA and is calling for increased legacy allowances,” explained Tom Swenson, Director of Global Regulatory Affairs.

Emission legislation passed by the California Air Resources Board (CARB) requires a Clean Air Act waiver from the EPA when it proves stricter than federal policy. CARB has been receiving federal waivers for its emissions policies since the 1960s given its ongoing battles with air pollution.

Geographical features such as valleys and mountains appearing throughout the state can hinder air circulation to keep pollutants hanging around.

“The San Joaquin Valley in California, for example, is like a little trap of NOx,” Uma Vajapeyazula, North American Market Strategy Director, described.

Eager to overcome its unique air pollution issues, CARB has kept a close eye on ZEV development. Once board members decided the technology was up to the challenge of replacing ICE trucks up to Class 8, CARB adopted the Advanced Clean Trucks (ACT) rule in June of 2020. To date, it’s the only one of the three ZEV polices that has received an EPA waiver.

 The ACT rule requires that manufacturers who certify chassis or complete vehicles with a gross vehicle weight rating (GVWR) greater than 8,500 lbs. sell zero-emission vehicles (ZEV) at an increasing percentage of their annual California sales starting with the 2024 model year. The annual reporting began with the 2021 model year.

 OEMs struggling to sell ZEVs can buy ZEV credits from other manufacturers to unlock sales of their ICE vehicles. However, there’s concern that funds used to purchase ZEV credits could impact their bottom line.

 “One question is, ‘Will ZEV credit trades happen between competitors?’” Swenson said.

In September 2021, CARB adopted the Heavy-Duty Engine and Vehicle Omnibus Regulation to “drastically cut smog-forming nitrogen oxides (NOx) from conventional heavy-duty engines. The Omnibus Regulation will significantly increase the stringency of NOx emissions standards and will also lengthen the useful life and emissions warranty of heavy-duty diesel engines for use in vehicles with a gross vehicle weight rating (GVWR) greater than 10,000 pounds. The more stringent NOx emission standards begin with the 2024 model year engines and become more stringent with 2027 and subsequent model year engines.”

 Extending warranty coverage will necessarily increase the cost of equipment, Swenson noted.

 Advanced Clean Fleet legislation rolled out next in April 2023. ACF requires fleets to gradually replace acquired ZEVs while allowing them to retain ICE vehicles throughout their useful life. Per CARB, useful life is defined “as the later of either: 1) 13 years, beginning with the model year that the engine in the vehicle and was first certified for use by CARB or United States Environmental Protection Agency (U.S. EPA), or 2) the date that the vehicle exceeds 800,000 vehicle miles traveled or 18 years from the model year that the engine in the vehicle was first certified for use by CARB or U.S. EPA (whichever is earlier).”

ACF compliance challenges

In August, EPA held an ACF waiver hearing that included a full day of testimony, comments were also accepted online. One of the companies to participate was Sundance Stage Lines in San Diego. The charter bus company currently uses diesel-powered custom-built buses with a 1,000-mile range and 20-minute refueling time. It has stated opposition to ACF’s zero-emission mandate.

“As BEVs, range is cut to approximately 200 miles (substantially less in cold weather), at which point the vehicle requires a four-hour charge at a dedicated high-voltage charger before it can proceed another 200 miles,” Sundance Stage Lines writes. “Thus, any group attempting to access an area not serviced by either an airport or a nearby charter operator will be forced to make other arrangements. This will have substantial negative effects both on motorcoach operators and the traveling public.”

Among the concerns expressed, Sundance noted that “four major motorcoach manufacturers offer at least one of their models as battery-electric vehicles (BEVs.) In converting the vehicle to run as a BEV, all of the buses have lost over 70% of luggage space because the volume of batteries needed to give the vehicle a reasonable range requires the batteries and the accessories normally driven by the engine be mounted in the underfloor luggage compartments.”

Sundance also pointed out the high cost of ZEVs versus ICE. In the case of motor coaches, the company contends the price “more than doubles, from $650,000 each to over $1,400,000 per bus - a cost per unit over twice as high as any other electric vehicle.”

In its ACF waiver request submitted last November to EPA, CARB writes that “anticipated developments will likely both reduce the costs and increase the number of commercially available ZEVs, including projected decreased costs of batteries and improvements in battery energy density due to economies of scale and increasing pace of technology development and decreased costs of other ZEV components resulting from the projected increased production of ZEVs.” 

Legal battles persist

At least three lawsuits that have emerged to challenge the enforcement of ACF make it California’s most contentious trucking legislation to date. 

The first complaint was filed in October 2023 by the California Trucking Association in the U.S. District Court for the Eastern District of California. The challenge has resulted in the state holding off full enforcement that was originally slated to go into effect on January 1, 2024. CTA’s 32-page complaint argues that the state needs a waiver from the Environmental Protection Agency prior to enforcing ACF since its policies exceed federal mandates.

In response, California put ACF enforcement on hold for most fleets pending receipt of an EPA waiver. CTA noted on its website that waivers typically take 9-12 months to process. The state has been enforcing ACF for public fleets since applying for the waiver in November

“They’re implementing and enforcing ACF for state [California] and local government fleets,” explained Mari Mantle, Cummins Regulatory Affairs Manager. “It's the high priority, federal and then drayage [fleets] that they're waiting on the waiver for.”

CTA’s complaint also highlights concerns of ZEVs relative to internal combustion. Acquisition costs of ZEVs, according to CTA, are “projected to be 2 to 6 times higher than comparable ICE tractors”; ZEV range “is less than half that of an ICE truck”; additional refueling stops needed for ZEVs will require additional time and infrastructure and thus limit more route options historically utilized by ICE trucks.

In April, American Free Enterprise Chamber of Commerce (AmFree Chamber) and Associated Equipment Distributors (AED) filed suit also challenging California’s ACF regulation.

In May, the Nebraska Trucking Association topped a list of plaintiffs that included seventeen states opposing ACF: Alabama, Arizona, Arkansas, Georgia, Idaho, Indiana, Iowa, Kansas, Louisiana, Missouri, Montana, Nebraska, Oklahoma, South Carolina, Utah, West Virginia and Wyoming. Several of these same states joined a suit last year against the Advanced Clean Trucks rule.

Tom Quimby headshot

Tom Quimby

Tom Quimby, On-highway Journalist, has a broad range of experience covering various topics for local and national periodicals. His stories and photos have appeared in The Washington Times and more recently in Commercial Carrier Journal, Overdrive, Hard Working Trucks, Equipment World and Total Landscape Care. Tom has reported on Class 1 – 8 commercial vehicles since 2015. A graduate of the University of Southern California, Tom enjoyed growing up around hot rods, dirt bikes, deserts and beaches near San Diego. He now calls Northwest Florida home.

STEM Project Unites Children in the UK and Uzbekistan

Zoom call with West Park School and the Children's Home

If you ever doubted the ability of young minds to grasp what many adults would consider complex concepts, then you'll be amazed by the achievements of two groups of young children - one in a school in northern England, and the other 4,000 miles away in an orphanage in Uzbekistan.

With the support of Cummins, children ranging from six to twelve years of age have managed to bridge the language, culture, and time divide. They are collaborating with great success on building a basic electric racing car.

The story begins with a visit by Cummins to Rudmash Export Service, which has been representing Cummins in Tashkent, the capital of Uzbekistan, since 2018.

Rudmash has an impressive list of clients in mining, construction, gas, and power generation.

It is also a highly respected supporter of community initiatives, a key focus for Cummins.

During the visit, Amit Kumar, Cummins' Technical Territory Manager for the Commonwealth of Independent States (CIS) region, mentioned the work he was doing with local schools involving the Greenpower Education Trust in the UK.

Amit suggested that Rudmash might consider introducing local children to the fantastic learning opportunity that comes from building an electric car.

The Rudmash executive team loved the idea and reached out to their friends at the local orphanage (Children’s Home 22), about the proposed connection with children from West Park Academy – a primary school near Cummins' manufacturing plant in Darlington, England.

Students at the Children's Home working on the car
The children from Children's Home 22 building the car

Speaking through a translator, Rudmash Sales Manager Mr. Mavlonberdi Akhmedov said there was no hesitation from the orphanage. "Everyone was excited about it," he said. "When we showed them pictures of the car, the children's eyes lit up with interest.

"The only issue we encountered was not being able to involve the older children, but I think Amit has something in his mind for them. It will involve a similar collaboration with a UK school on a larger electric car that they can fit in!"

Over in Darlington, teacher Mr. David Fraser and his group of 9 to 11-year-olds were thrilled at the prospect of working with children from another country.

Students from West Park Academy
The children from West Park Academy

"Before our first session, I showed the children a map of Uzbekistan and explained how the time zones worked," Mr. Fraser said. "Tashkent is four hours ahead of us."

"When they started hearing a different language, they were a little hesitant although still excited. However, towards the end, once they got used to the translation pauses, lots of questions were being asked."

"They adapted very quickly, and every session with the orphanage has become more engaging. The children have greatly benefited from the relationship. It's been a great learning experience."

The car involved in the project is called the Greenpower Goblin G2. It comes as a flat-pack kit including chassis, wheels, steering, disc brakes, a 24V electric motor, and two 12V batteries.

Students at West Park Academy working on the car
The children from West Park Academy building the car

"The project is all about inspiring young children to take an interest in engineering in a fun and innovative way," said Amit Kumar, who earlier this year received special recognition at the North-East England STEM (Science, Technology, Engineering, and Mathematics) Awards for his years of dedication to STEM Education.

"The build introduces children to basic mechanics and electronics and might be the first step on the pathway to a career in engineering or another STEM field.

Mr. Fraser said the children soon started discussing aspects of the car such as frames, brakes, and steering geometry. There was a lively question-and-answer session on different materials that could be used to design and make the car's body. Their last session was about controls and driving.

"There are also other general discussions, as the children are eager to learn more about each other's countries," said Amit, who leads the sessions.

Students at the Children's Home looking at the car drawing
The children from Children's Home 22 talking about a drawing while on a zoom call

Rudmash service engineer Mr. Abdullayev Shakhzod said the children were enjoying the experience of working in teams.

"It's a fantastic new chapter in the history of a place that has a storied past. It was established in 1942 during the Second World War to care for evacuees from all over Eastern Europe. Children of over 40 different nationalities have been cared for by this children's home.

"The home is named Antonina Pavlovna Khlebushkina after the woman who ran it in the early days. She would be so proud of what is happening there today.

"As the summer vacation times differ in the two countries, the West Park school children have already finished building their cars, while the Uzbekistan car is about 40% complete.

"When the children return from their summer camp in September, they will start the rear axle, motor, and electrical components. Then they can take it for a drive," Amit said.

"Just before their summer term ended, the West Park children conducted a demonstration for their new friends in Tashkent. They set up a track and showcased driving the car on it. It was a great success."

Mr. Akhmedov, speaking through a translator, mentioned that the management team at Rudmash was considering how the project could expand beyond the children's home and into schools and youth organizations throughout Uzbekistan.

Mr. Akhmedov praised Cummins for their support of the project. "They have shown great responsibility at every stage and been very proactive, always striving to ensure things are done right.

"This is just the beginning for these children. It's already motivating them to learn more and develop their skills in broader technical applications.

"I would say that this project is not only important for the children's home but also for our city of Tashkent and the Republic of Uzbekistan, as it is nurturing an educational culture that is highly valuable. I can't thank Amit and Cummins enough."

Amit expressed that it's a privilege to help Cummins inspire young people about engineering and science from an early age.

Redirecting to
cummins.com

The information you are looking for is on
cummins.com

We are launching that site for you now.

Thank you.